You can set the trusted/optional depending on where you want each vlan to go in that watchguard. Basically I’m going to have 4 VLANs: Trusted devices (wired and wireless), IoT, Printer, Guest. – Make sure your printer’s IP address & gateway are set correctly for VLAN20. You can’t configure the access point by directly connecting to it. And they both should be a guest network. I beleive the default DHCP is 192.168.2.0 / 24 (255.255.255.0) No pre-authorization, when connected, can’t ping the router, but can ping a DNS server (Google) and can’t access the internet. While I understand that this is what the agent is designed to do, and have no reason to believe that this was intentional by anyone, I still have a privacy concern about this.
Something like that would be a quick setup without knowing all the nitty gritty of your network. I've only changed the options in the picture. The very first step is to create the new VLAN. I hope this article helpt you settings up your Unifi Guest Portal.
Yeah, that would separate IoT devices from your main network. I have successfully implemented the configuration as shown. Go to Settings->Routing & Firewall and find the Firewall tab. Within the Unifi Controller under the Guest Control section, we can create our Guest Portal, set the authentication and duration of access. After the client is authorized, the post, you allow access to the whole subnet /24, Are you shure? This would prevent any IoT devices (if compromised) to try to tap into your Blue Iris server. Go into ‘Wireless Networks’ and Edit the guest WiFi network.

We have 500/500 now so not sure how a 1 X gbe interface will handle it, I could look at combining two physical interfaces into 1 for external to internal network but it's not a priority. Pre and Post-Authorization Access. is that possible? Those rules may also work, but I went through much troubleshooting and re-wrote the firewall rules many times. By default, all possible local network address are blocked, so you could leave this as is. The only way to fix this is to install a cert, but that is not really easy todo.

This isn’t even really a guest WiFi – we just want to isolate staff BYOD so they can use WiFi on their phones etc, but keep them discrete from the company hardware. How to access your modem webui whilst using sense, How to access your modem webui whilst using pfsense. With the first 2 parts done, the home network is already using pfSense and VLAN with multiple sub-networks. Do you have any suggestions about how to allow printing from iPhones and iPads connected to VLAN40 or VLAN44? I believe the V1 switches needed a utility that was only available for Windows, which is no use to me as I'm using Antergos as my operating system. Great! Well Done! On some screens, this will result in borders besides your image. In a Watchguard a "Bridge" simply means that you bonded multiple ports together on the device (rather like a conventional residential router). The HP switch in the middle has a rather complicated GUI.

We don’t need to manage the devices from cloud.

Based on this we’ll be setting up a Guest network for our DMZ VLAN. View this "Best Answer" in the replies below ». Also what do you mean by bridging, as in you configure a seperate inf on the WG then bridge it to your trusted int? Thank you, Alan. thanks for this excellent piece. add new rule: source: Subnet1 net, source port: *, destination: VLAN20 net, dest port: * If the controller isn’t doing the DHCP, then your client won’t get an IP Address. It should identify your printer and print successfully. You need to create firewall rules at Subnet1 and VLAN40 to allow traffic to VLAN20. Setup Pfsense & Unifi with Guest Wifi VLAN. This was really helpful, thank you so match! I understand how to use a remote access VPN from outside the home to access the home LAN, but not sure how to safely hop subnets while at home? In UniFi this is done by going to Settings -> WI-FI -> Wi-Fi Networks. Set protocol to Any. So if you have a controller running on your computer that you turn off or take with you, then you really need to buy the Unifi Cloud key. Apparently there are no posts at the moment, check again later. I have a openVPN server on pfSense and my laptop connected through wi-fi. This allows us to set upload and download limits for the guests later on.