First what's the default gateway of the PC - Lan or Wifi? I have a desktop connected to my router. Basically I would like to access the controller from my work or on the road to deal with any problems. eNMok To find which IP address your UniFi is, on the back on your physical UniFi product, there is a “MAC ID”, compare the last 12 numbers to the MAC address’s listed in the DHCP Table.Windows Server:Login to your Windows Server, in your start menu, go to Administrative Tools > DHCP Expand your DHCP domain and go to the scope for which you’ve got your UniFi’s plugged into. so use cmd prompt 'route print' to check the routes and look carefully at the metrics to see which interface is being used. Because our controller is sitting on a different subnet, broadcasts get stopped at the router and are unable to make it to the controller software. by Mikrotik:Login to your Mikrotik router, and via CLI enter the following line: /ip dns static add name=unifi address=192.168.10.2Windows Server:Login to your Windows Server, in your start menu, go to Administrative Tools > DNSExpand your DNS server name and go to Forward Lookup Zones. UniFi® Access Lite. Just make sure to name them so you know what is what. From there, you can also change auto-generated password to something easier to memorise.Once, re-connected via SSH, issue the same commands again. Press J to jump to the feed. Once you’re logged into the Unifi Controller, go to the Unifi Cloud Site to access your controller from the internet using your Unifi account. Do I need to move the controller on a public IP address ? I've confirmed with https://help.ui.com/hc/en-us/articles/218506997-UniFi-Ports-Used that UDP port 3478, TCP ports 8080, 8443, 8843, and 6789 are all open and forwarding to this Windows PC at the 192.168.100.xxx IP. To find which IP address your UniFi is, on the back on your physical UniFi product, there is a “MAC ID”, compare the last 12 numbers to the Unique ID listed in the DHCP Table.Once you’ve got the IP Address on your unit, use an SSH program such as putty to establish a connection to the AP.If you’ve got a new out of the box unit, the default credentials are:Username: ubntPassword: ubntOnce logged in, enter the following commands, and remember to replace 192.168.10.2 with the address of your controller, Then if you go to your controllers homepage and go to Access Points and you should see your access point in the list (you can verify this with checking IP Address you where connecting too).Click Adopt next to the AP, and refresh the page until the AP comes back with a status of ‘Connected’ (It may need to upgrade the firmware on the AP)Once it’s connected, you will need to re-SSH to the AP, in which it will now have the username/password credentials that are set by your controller.If you don’t know this, the device login username and password can be found in the controller software.
May 31, 2020 at 00:56 UTC. any suggestions? The Ubiquiti UniFi Cloud Key Controller (UC-CK) will allow you to manage multiple products and access points from the UniFi family whilst maintaining full fuctionality on a compact device with minimal power consumption. Press question mark to learn the rest of the keyboard shortcuts. The following snippet shows how I did it. UniFi® Access Card.
New comments cannot be posted and votes cannot be cast. You do not need to open ports or do anything with your router. Second-generation product family Designed from the ground up..
Another possible situation you might also encounter with regards to the default username and password of the UniFi Access Point, is if the AP has had SSH already enabled within the UniFi Controller Software.You can double check if this is the case by logging into the UniFi Controller Software, then click the tiny gear icon in the bottom left corner to go to the settings page – on this … Set up a cloud key or controller in each site and allow online access. UniFi® Security Gateway. Folks, I am a little confused and need some help. I had the early access version of the reader and controller sent to me. You can setup cloud access for unifi.ubnt.com by going to cloud access on the controller. UniFi® Access Hub. UniFi® LTE. The first check may not be so straight forward - if DHCP is enabled on both LAN and Wifi it is likely that both are sending a default gateway. unable to connect to Ubiquiti UniFi controller remotely, https://help.ui.com/hc/en-us/articles/218506997-UniFi-Ports-Used. Additionally, UDM-Pro offers advanced features such as topology diagrams, device identification, Intrusion Prevention and Deep Packet inspection features not available on locally hosted controllers. Select your DNS Zone for which your device will be sitting in & right click on it and select New Host (A or AAAA).For the name, enter in “unifi” without the quotes, and for the IP address, put the address of your UniFi server. If you want to keep your access points up-to-date and use the guest features at home, then this is where the Cloud Key comes in. Because our controller is sitting on a different subnet, broadcasts get stopped at the router and are unable to make it to the controller software. Did you find it helpful? Thus the same in return for the controller software looking for the access points. It should look something like