If you see people spreading misinformation, trying to mislead others, or other inappropriate behavior, please report it!

A critical part of what differentiates each model is the number, arrangement, and orientation of the AP’s antennas—which influences the shape and behavior of wireless signal (both on transmit and receive).

Ubiquiti UniFi nanoHD The UniFi nanoHD wireless access point is a compact (smaller than the other UniFi APs) 802.11ac Wave2 device with MU-MIMO technology. If you haven’t already been descriptive in your post, please take the time to edit it and add as many useful details as you can.

The AP in the picture would actually be near the back door, so it should cover the porch well. Apply Unifi online now at RM0 cost.

Check out latest Unifi promotions and offers. Add another if needed. Technology platforms for Internet Access, Enterprise, and SmartHome applications. I kinda wish NanoHD, FlexHD, and BeaconHD's antennas were bigger. And if you want coverage outside for while you're mowing or something, consider a third. Limited time only. FREE Installation. I'd plan on adding a second AP if I were you. The picture is merely green - but I don't know if that is decent or really bad when compared to the red. You're going to want two AP's. You’ll need two to get good coverage in a house with that layout. Real-World Performance The UniFi nanoHD AP is the UniFi 802.11ac Wave 2 AP with the smallest form factor. Press question mark to learn the rest of the keyboard shortcuts. Ubiquiti UniFi nanoHD UAP-nanoHD IEEE 802. I have a ranch house (single story) that is basically a 70 foot by 30 foot rectangle.

UniFi est un système révolutionnaire qui combine performances WiFi, évolution illimitée, coût restreint et outil de gestion virtuel centralisé. Copyright 2020 unifi-TM Package | All Rights Reserved | Powered by. Category: Ubiquiti Wireless Access Points. Question. Mine are mounted vertically on the walls and cover both floors and the basement adequately. Point d'accès intérieur Ubiquiti UniFi UAP-AC-LR 802.11ac. I have recently bumped up my internet package to 600 mbit/sec and will be getting a newer modem to support it. Why would having a single AP mean that I would need better access to the 2.4 range?

A direct speed test on the wire showed 700-800 but their Orbi mesh system only shows 200-300 on WiFi. A friend has a giant house and got up sold to Fios gigabit speeds. Since my internet package will be 600 mbps, I would like to get a setup that can give me at least 500 in the living room (where the picture AP is) and in the office (bottom left of the image. And going with all Unifi APs let them handoff quite smoothly in my experience. Press J to jump to the feed.

So there are a lot of posts debating the merits of WiFi 6 vs WiFi 5 between the two, and I am not going to really go much into that because honestly the only WiFi 6 device I have is my phone and I don't really do anything that needs that kind of speed.

You’ll need two to get good coverage in a house with that layout. The standard package is inclusive of equipment worth approximately RM1,000 that will also be given free-of-charge to customers. Or at least plan on doing it in the future if you can't right now.

Right now I have a Netgear R6700v2 sitting in that approximate area (though of course not on the ceiling, and my ~220 mbit/sec connection is dropping down to 50 or so. The UniFi AP Beacon HD is the fastest way to extend Wi-Fi coverage and increase throughput.

UniFi Coverage. They refuse to downgrade so I have half a mind to buy MoCA adapters and wire the house that way.

So if I put a NanoHD in this spot on the ceiling, what network speeds should I expect in the green area toward the bottom-left of this picture? These are still the only ubnt indoor aps we run. SAVE up to RM200 of installation fee for your Unifi fibre optic installation.

Also the heat map is a scale in dB's. Run an Ethernet cable to any device that you want to take advantage of your internet speeds.

This is an unofficial community-led place to discuss all of Ubiquiti's products, such as the EdgeRouter, UniFi, AirFiber, etc.

Avoid queuing and waiting at the counter. You can draw walls and tell it the type of wall and all of that with their floorplan designer as well, but even then I wouldn't 100% rely on it being too accurate. Detail. Mine are mounted vertically on the walls and cover both floors and the basement adequately.

Combining the performance increases from MU-MIMO technology and the use of 4x4 spatial streams, the UniFi nanoHD AP delivers up to 125% greater performance1 than a typical Wave 1 AP. I have about the same size house with a nanoHD in almost the same spot. I can't find any documentation on this part of the UI. AP Signal - UniFi 6 Lite VS UniFi NanoHD. I have a two story house narrower than yours and to get complete coverage, I need a NanoHD at each end of the house. Get latest Unifi Promotion. SAVE up to RM200 of installation fee for your Unifi fibre optic installation. So just like every other UniFi product that we’ve tried, the NanoHD … They are dirt cheap, will cover your BW requirements. Do you know if, for a single story, mounting horizontally or vertically is better? That’s with playing with all the radio adjustments and different channels. Centrally located on the second floor (where my office is, which is helpful), I get just about my full up/down. I keep waffling between the various APs.